[ 0.000000] Linux version 3.18.20 (dtech@itsuki.dev.dtech.hu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46767) ) #154 Sat Jan 7 16:47:59 CET 2017 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR7242 rev 1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff] [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] free_area_init_node: node 0, pgdat 8034e0f0, node_mem_map 81000000 [ 0.000000] Normal zone: 64 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8192 pages, LIFO batch:0 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: console=ttyS0,115200 GPIO_RESET=yes gpio=790341 HZ=200000000 mem=32M board=groove boot=0 mlc=2 rootfstype=yaffs noinitrd [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 28524K/32768K available (2448K kernel code, 154K rwdata, 516K rodata, 200K init, 184K bss, 4244K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100000] NET: Registered protocol family 16 [ 0.100000] MIPS: machine is MikroTik RouterBOARD SXT 5HnD [ 0.110000] ar71xx: pll_reg 0xb805002c: 0x62000000 [ 0.110000] Groove/SXT eth0: disabled. [ 0.110000] Groove/SXT eth1: enabled, using mac=00:0c:42:88:aa:34. [ 0.150000] registering PCI controller with io_map_base unset [ 0.160000] PCI host bridge to bus 0000:00 [ 0.160000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.170000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.170000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.180000] pci 0000:00:00.0: [168c:ff1c] type 00 class 0x020000 [ 0.180000] pci 0000:00:00.0: fixup device configuration [ 0.180000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit] [ 0.180000] pci 0000:00:00.0: supports D1 [ 0.180000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.180000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.180000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit] [ 0.190000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.190000] Switched to clocksource MIPS [ 0.200000] NET: Registered protocol family 2 [ 0.200000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.200000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.210000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.220000] TCP: reno registered [ 0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.230000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.230000] NET: Registered protocol family 1 [ 0.240000] PCI: CLS 0 bytes, default 32 [ 0.240000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.250000] yaffs: yaffs built Dec 21 2015 20:36:36 Installing. [ 0.250000] msgmni has been set to 55 [ 0.280000] io scheduler noop registered [ 0.280000] io scheduler deadline registered (default) [ 0.290000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.290000] console [ttyS0] disabled [ 0.320000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A [ 0.330000] console [ttyS0] enabled [ 0.330000] bootconsole [early0] disabled [ 0.340000] NAND flash driver for the RouterBOARD 750 version 0.1.0 [ 0.350000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x76 [ 0.360000] nand: Samsung NAND 64MiB 3,3V 8-bit [ 0.360000] nand: 64MiB, SLC, page size: 512, OOB size: 16 [ 0.370000] Scanning device for bad blocks [ 0.390000] Bad eraseblock 340 at 0x000000550000 [ 0.680000] Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit": [ 0.680000] 0x000000000000-0x000000040000 : "booter" [ 0.690000] 0x000000040000-0x000000400000 : "kernel" [ 0.700000] 0x000000400000-0x000004000000 : "rootfs" [ 0.700000] mtd: device 2 (rootfs) set to be root filesystem [ 0.710000] mtdsplit: no squashfs found in "rootfs" [ 0.720000] mtdsplit: no squashfs found in "NAND 64MiB 3,3V 8-bit" [ 0.760000] libphy: ag71xx_mdio: probed [ 0.760000] AG7240: Length per segment 1544 [ 0.760000] AG7240: Max segments per packet 1 [ 0.770000] AG7240: Max tx descriptor count 80 [ 0.770000] AG7240: Max rx descriptor count 252 [ 0.780000] AG7240: fifo cfg 3 01f00140 [ 0.780000] AG7240CHH: Mac address for unit 0 [ 0.790000] AG7240CHH: 00:00:00:00:00:00 [ 0.990000] AG7240CHH: Mac address for unit 1 [ 1.000000] AG7240CHH: 00:0c:42:88:aa:34 [ 1.200000] TCP: cubic registered [ 1.200000] NET: Registered protocol family 17 [ 1.210000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.220000] 8021q: 802.1Q VLAN Support v1.8 [ 1.230000] rb: no calibration data found [ 1.240000] yaffs: dev is 32505858 name is "mtdblock2" ro [ 1.240000] yaffs: passed flags "" [ 1.240000] yaffs: yaffs: Attempting MTD mount of 31.2,"mtdblock2" [ 1.250000] yaffs: block 85 is bad [ 6.830000] yaffs: yaffs_read_super: is_checkpointed 0 [ 6.830000] VFS: Mounted root (yaffs filesystem) readonly on device 31:2. [ 6.840000] Freeing unused kernel memory: 200K (8036e000 - 803a0000) [ 7.230000] init: Console is alive [ 7.230000] init: - watchdog - [ 8.260000] usbcore: registered new interface driver usbfs [ 8.270000] usbcore: registered new interface driver hub [ 8.270000] usbcore: registered new device driver usb [ 8.390000] SCSI subsystem initialized [ 8.410000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.420000] ehci-platform: EHCI generic platform driver [ 8.420000] ehci-platform ehci-platform: EHCI Host Controller [ 8.430000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 8.440000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 8.460000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 8.460000] hub 1-0:1.0: USB hub found [ 8.470000] hub 1-0:1.0: 1 port detected [ 8.480000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.480000] ohci-platform: OHCI generic platform driver [ 8.500000] usbcore: registered new interface driver usb-storage [ 8.790000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 8.940000] usb-storage 1-1:1.0: USB Mass Storage device detected [ 8.940000] scsi host0: usb-storage 1-1:1.0 [ 9.280000] init: - preinit - [ 9.590000] random: mktemp urandom read with 44 bits of entropy available [ 9.950000] scsi 0:0:0:0: Direct-Access WD Ext HDD 1021 2002 PQ: 0 ANSI: 4 [ 9.960000] sd 0:0:0:0: [sda] 1465143296 512-byte logical blocks: (750 GB/698 GiB) [ 9.970000] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled [ 9.980000] sd 0:0:0:0: [sda] Asking for cache data failed [ 9.980000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 10.360000] sda: sda1 sda2 [ 10.370000] sd 0:0:0:0: [sda] Attached SCSI disk [ 12.730000] mount_root: mounting /dev/root [ 12.740000] mount_root: loading kmods from internal overlay [ 12.940000] block: attempting to load /etc/config/fstab [ 12.940000] block: extroot: not configured [ 13.000000] procd: - early - [ 13.000000] procd: - watchdog - [ 13.330000] EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem [ 13.510000] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: [ 13.620000] procd: - ubus - [ 14.630000] procd: - init - [ 15.880000] NET: Registered protocol family 10 [ 15.900000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 15.930000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 15.940000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 15.950000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 15.970000] nf_conntrack version 0.5.0 (448 buckets, 1792 max) [ 16.000000] usbcore: registered new interface driver ums-alauda [ 16.010000] usbcore: registered new interface driver ums-cypress [ 16.020000] usbcore: registered new interface driver ums-datafab [ 16.030000] usbcore: registered new interface driver ums-freecom [ 16.040000] usbcore: registered new interface driver ums-isd200 [ 16.040000] usbcore: registered new interface driver ums-jumpshot [ 16.050000] usbcore: registered new interface driver ums-karma [ 16.060000] usbcore: registered new interface driver ums-sddr09 [ 16.070000] usbcore: registered new interface driver ums-sddr55 [ 16.080000] usbcore: registered new interface driver ums-usbat [ 16.110000] xt_time: kernel timezone is -0000 [ 16.150000] cfg80211: Calling CRDA to update world regulatory domain [ 16.210000] cfg80211: World regulatory domain updated: [ 16.220000] cfg80211: DFS Master region: unset [ 16.220000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 16.230000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 16.240000] cfg80211: (5140000 KHz - 5860000 KHz @ 160000 KHz), (N/A, 3000 mBm), (N/A) [ 16.390000] PPP generic driver version 2.4.2 [ 16.390000] NET: Registered protocol family 24 [ 16.500000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 16.520000] ath: phy0: eeprom contains invalid mac address: 29:29:01:55:f2:83 [ 16.520000] ath: phy0: random mac address will be used: b6:8a:63:a8:b0:7e [ 16.530000] ath: EEPROM regdomain: 0x0 [ 16.530000] ath: EEPROM indicates default country code should be used [ 16.530000] ath: doing EEPROM country->regdmn map search [ 16.530000] ath: country maps to regdmn code: 0x3a [ 16.530000] ath: Country alpha2 being used: US [ 16.530000] ath: Regpair used: 0x3a [ 16.550000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 16.560000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40 [ 16.570000] cfg80211: Calling CRDA for country: US [ 16.570000] cfg80211: Regulatory domain changed to country: US [ 16.580000] cfg80211: DFS Master region: unset [ 16.580000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 16.590000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 16.600000] cfg80211: (5140000 KHz - 5860000 KHz @ 160000 KHz), (N/A, 3000 mBm), (N/A) [ 19.600000] random: nonblocking pool is initialized [ 23.100000] ag7240_ring_alloc Allocated 1280 at 0x80e67800 [ 23.100000] ag7240_ring_alloc Allocated 4032 at 0x80f92000 [ 23.110000] reg init for 1 [ 23.110000] ATHRS26: resetting s26 [ 23.220000] ATHRS26: s26 reset done [ 23.220000] Setting PHY... [ 24.230000] device eth1 entered promiscuous mode [ 24.230000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 24.840000] AG7240: enet unit:1 phy:0 is up...Mii 100Mbps full duplex [ 24.840000] AG7240: done cfg2 0x7315 ifctl 0x0 miictrl [ 24.880000] br-lan: port 1(eth1) entered forwarding state [ 24.880000] br-lan: port 1(eth1) entered forwarding state [ 25.090000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 26.880000] br-lan: port 1(eth1) entered forwarding state